Features:
- Deterministic Auxiliary Processing for Mark VIe
- Ruggedized Conformal Coating & Thermal Tolerance
- Deep Diagnostic Visibility with ±2°C Precision
The General Electric IS210BPPBH2BKD offloads thermal management and diagnostic tasks from the primary controller. By acting as a dedicated co-processor, it ensures that the main CPU remains focused on high-speed turbine protection logic (e.g., over-speed detection), reducing jitter and improving response times in emergency shutdown scenarios.
To survive the corrosive environments found in turbine enclosures, the General Electric IS210BPPBH2BKD utilizes a conformal coating that protects sensitive circuits from conductive contaminants. Rated for extreme temperatures (-40°C to +85°C) and high vibration, this board ensures continuous operation in combined-cycle plants without failure due to moisture ingress or thermal cycling fatigue.
Engineers can perform rapid fault isolation using the onboard dual-LED status indicators and physical test points on the General Electric IS210BPPBH2BKD. The integrated temperature sensor provides live monitoring with ±2°C accuracy, allowing the Mark VIe system to trigger predictive alarms before thermal stress warps the backplane connectors, thus preventing costly unplanned outages.
The IS210BPPBH2BKD General Electric Mark VIe Turbine Auxiliary Processor Board may still be available for purchase and support from Apter Power beyond End-Of-Life (EOL) by the manufacturer (OEM).
General Electric IS210BPPBH2BKD Mark VIe Turbine Auxiliary Processor Board Manuals,Datasheets,Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
General Electric IS210BPPBH2BKD Mark VIe Turbine Auxiliary Processor Board
General
- Manufacturer General Electric
- Model IS210BPPBH2BKD
- Condition New Original ready stock
- Product Family IS210BPPCH1AEC,IS210BPPCH1AD,IS210BPPCH1ACA
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
- Heavy-Duty Gas Turbines (GE Frame 6FA/7EA): Executes auxiliary logic for inlet bleed heat control and compressor surge prevention, reducing load on the primary turbine controller.
- Steam Turbine Retrofit Projects: Adds processing headroom for older turbines being modernized with digital electro-hydraulic (DEH) control systems.
- Combined-Cycle Plants (CCPP): Serves as the data concentrator for heat recovery steam generator (HRSG) interface, synchronizing steam bypass logic with gas turbine output.
- Offshore Power Generation: Its conformal coating makes it suitable for salty, humid environments where standard industrial cards fail within months due to galvanic corrosion.
- Precision Thermal Feedback: The onboard ±2°C sensor provides direct analog input to the Mark VIe TMR (Triple Modular Redundant) safety logic, initiating runback procedures before the lubricating oil degrades.
- Diagnostic Test Points (DTPs): Allows engineers to use oscilloscopes to measure logic-level signals (5V/10A rails) live, verifying power integrity during turbine startup without software polling delays.
- Deterministic Data Bridging: Filters raw vibration data from proximity probes into usable "Peak-to-Peak" values via Modbus, offloading FFT calculations from the main CPU to maintain steady-state scanning.
- Status Annunciation (LEDs): Offers "Heartbeat" and "Fault" indicators that blink in specific binary patterns to indicate exact failure modes (e.g., RAM corruption vs. Comm loss), even if the HMI is frozen.
- IEC 61508 (SIL 2 Capable): Designed for use in Safety Instrumented Functions (SIFs) up to SIL 2 when integrated with the Mark VIe Safety Net, handling non-critical trips like high generator bearing temperature.
- Dielectric Withstanding Voltage: The PCB material (FR-4 epoxy) is rated to withstand 1500V AC RMS for 60 seconds between primary power and ground, preventing arc flash propagation.
- RoHS & REACH Compliance (Select Revisions): While some legacy units contain leaded solder, the General Electric IS210BPPBH2BKD "H2BKD" suffix typically corresponds to RoHS-compliant manufacturing for export to EU markets.
- Vibration Resistance (IEC 60068-2-6): Tested to withstand 5g peak acceleration from 10-500Hz, ensuring solder joints do not crack under the low-frequency rumble of turbine skids.