Features:
- 130 mm overall case length reaches through thick casings or insulation, eliminating standoffs and adapters in deep-well mounting applications.
- FluidLoc cable technology with a 5.0-meter integral length combines fluid containment and extended reach in a single assembly.
- Country-specific approvals for Russia simplify compliance, allowing direct installation in local facilities without extra certification steps.
The 330103-00-13-50-12-RU is built for situations where the probe has to travel a long distance from the mounting surface to the target. Its 130 mm case length lets it pass through thick turbine casings, heavy compressor walls, or multiple insulation layers without adding spacers or custom mounting hardware.
With a 5.0-meter FluidLoc cable, the 330103-00-13-50-12-RU handles two common installation challenges at once: remote Proximitor placement and fluid migration prevention. The extended length lets the sensor live in a control cabinet away from the machine, while the FluidLoc barrier inside the cable blocks oil from wicking through and leaking at the penetration point.
he 330103-00-13-50-12-RU carries country-specific approvals for Russia, so it can be used in local facilities without navigating separate certification processes. Its 8 mm construction adds mechanical toughness: the coil is encased in thicker PPS plastic than 5 mm probes, and the larger body diameter resists bending and vibration.
The 330103-00-13-50-12-RU Bently Nevada 3300 XL 8 mm Proximity Probes may still be available for purchase and support from Apter Power beyond
End-Of-Life (EOL) by the manufacturer (OEM).
Bently Nevada 330103-00-13-50-12-RU 3300 XL 8 mm Proximity Probese Manuals,
Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not
included with this equipment unless listed in the above stock item description. All prices are
shown in USD.
Bently Nevada 330103-00-13-50-12-RU 3300 XL 8 mm Proximity Probes Specs
General
- Manufacturer GE / Bently Nevada
- Model 330103-00-13-50-12-RU
- Condition New Original ready stock
- Product Family
330103-00-13-50-01-RU,330103-00-13-50-02-RU,330103-00-13-50-12-00
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not
included with this equipment unless listed in the above stock item description. All prices are
shown in USD.
- Radial Vibration Monitoring: Measures the relative dynamic vibration of the shaft in fluid thin-film bearings (sliding bearings) to diagnose imbalance, misalignment, or bearing wear.
- Axial Displacement Monitoring: Monitors the condition of thrust bearings to prevent axial collisions between the rotor and stator.
- Speed and Phase Reference (Keyphasor): Detects keyways or protrusions on the shaft, providing accurate speed pulses and phase references.
- Regional Compliance: The RU marking ensures that this component complies with Russian and related regional technical regulations and explosion-proof safety standards, suitable for local oil, gas, and power industry projects.
- "Not OK" Self-Diagnosis: When the probe cable is open-circuited or short-circuited, the downstream monitoring system (such as the 3500 series) will detect the signal abnormality and trigger the "Not OK" state, thereby preventing erroneous alarms and tripping.
- Connection Protection (Option 12): This model has a built-in connector protector that effectively prevents moisture and oil from entering the coaxial connector, reducing signal interference or electrical corrosion caused by poor contact.
- Chemical and Pressure Protection: The probe tip is encapsulated in PPS (polyphenylene sulfide) plastic with a Viton O-ring seal, resisting corrosion from high-temperature, high-pressure lubricating oil in the bearing housing.
- During installation, a 3300 XL preamplifier (Proximitor) is required. The DC output voltage should be measured using a multimeter.
- The gap is typically set at the center of the linear range (approximately -10.0 VDC) to ensure sufficient measurement space for both positive and negative vibrations.
- ClickLoc Connector: Employs 12-option ClickLoc technology with a self-locking mechanism to prevent loosening of the connector due to prolonged vibration.