Features:
- 6.5-meter length provides extended reach between probe and Proximitor sensor for flexible installation layouts.
- Backward compatible with 3300 RAM extension cables, enabling partial system upgrades without replacing all components.
- Connector protector seals the connection against moisture, eliminating field-applied tape.
Keep your existing probes and cables. Swap only the Proximitor sensor to NSv. The 330930-065-03-00 works with your current RAM components—lower cost, less downtime. Why replace hardware that's still performing well? The 330930-065-03-00 is mechanically and electrically compatible with your existing RAM probes and extension cables, meaning no rewiring, no recalibration, and no tearing apart control cabinets. Simply replace the Proximitor sensor with an NSv version, and you're done.
3000 and 7000-series require full component replacement. The 330930-065-03-00 is part of that new ecosystem. New probe, new cable, new Proximitor—full NSv performance. The technology gap between these legacy systems and NSv is too wide for piecemeal upgrades. When moving from 3000 or 7000-series 190 systems, every component must be replaced: probe, extension cable, and Proximitor sensor.
The connector protector comes pre-installed. No silicone tape, no field compounds. The 330930-065-03-00 seals against humidity right out of the box. Field-applied silicone tape is messy, inconsistent, and easy to mess up. One wrinkle, one gap, and moisture finds its way into the connection. The 330930-065-03-00 eliminates this variable with a factory-installed connector protector that seals the connection reliably every time.
The 330930-065-03-00 Bently Nevada 3300 NSv Extension Cable may still be available for purchase and support from Apter Power beyond End-Of-Life (EOL) by the manufacturer (OEM).
Bently Nevada 330930-065-03-00 3300 NSv Extension Cable Manuals, Datasheets, Drivers, Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
Bently Nevada 330930-065-03-00 3300 NSv Extension Cable Specs
General
- Manufacturer GE / Bently Nevada
- Model 330930-065-03-00
- Condition New Original ready stock
- Product Family
330930-040-03-00,330930-045-03-00,330930-065-00-00
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not
included with this equipment unless listed in the above stock item description. All prices are
shown in USD.
- Small-diameter machines: Particularly suitable for centrifugal air compressors, refrigeration compressors, and process gas compressors with a shaft diameter less than 51 mm (2 in).
- Confined installation space: Applicable to counterbores, areas with limited side or rear views where standard probes cannot operate properly.
- Hydrodynamic bearing monitoring: Provides radial vibration, axial displacement, speed (Tachometer), and keyphasor (phase reference) signals.
- Temperature Resistance: Operating and storage temperature range is -51°C to +177°C (-60°F to +351°F).
- Chemical and Corrosion Protection: The cable uses FEP (fluorinated ethylene propylene copolymer) insulation, providing excellent resistance to chemical corrosion.
- Physical Protection Specifications: The suffix 03 in the model designation indicates a design without stainless steel armor, but equipped with a connector protector to effectively prevent liquid intrusion into the gold-plated connectors.
- Signal Integrity: Maintains low-noise transmission between the probe tip and the Proximitor sensor. Output voltage is proportional to the gap distance, with a typical sensitivity of 7.87 V/mm (200 mV/mil).
- Precise Positioning and Gap: With the NSv probe, the recommended gap setting is typically -9 Vdc (approximately 1.0 mm), with a linear range of approximately 1.5 mm (60 mils).
- System Interchangeability: Supports Bently Nevada's ClickLoc gold-plated coaxial connectors, enabling locking connections without special tools, and allowing for complete interchangeability of system components without recalibration.