Features:
- Measures static shaft position and dynamic machine vibration.
- Supports vibration, position, Keyphasor reference, and speed monitoring.
- Enables interchangeability with compatible 3300 XL system components.
Bently Nevada 330101-00-16-10-11-00 supports condition monitoring programs for rotating machinery equipped with fluid-film bearings. Accurate shaft vibration and position information helps operators assess machine behavior during startup, steady operation, and shutdown. The proximity probe detects changes in the gap between its tip and a conductive shaft surface. Such measurements can contribute to early identification of abnormal shaft movement. Industrial users can integrate the probe into machinery protection and diagnostic systems.
The compact mechanical arrangement of Bently Nevada 330101-00-16-10-11-00 suits mounting points that require a 3/8-24 UNF threaded probe. A 0.0-inch unthreaded section allows the threaded body to extend close to the sensing end, while the 1.6-inch case length supports relatively compact installation. The 1.0-meter total length provides a direct cable path to the associated extension cable connection. A connector protector helps shield the miniature coaxial ClickLoc connection during installation and service. FluidLoc cable construction provides an additional practical advantage in environments where fluid migration along the cable could affect reliability.
For operational use, Bently Nevada 330101-00-16-10-11-00 forms part of a three-component measurement chain. The probe senses target distance, the extension cable carries the signal, and the Proximitor Sensor converts the response into a usable voltage output. Maintenance teams can apply the resulting signal to monitor radial vibration, axial position, rotational speed, or Keyphasor reference information. Component interchangeability simplifies replacement planning because compatible probes, cables, and sensors do not require individual matching or bench calibration. Backward compatibility with applicable non-XL 3300 Series components can also support maintenance of established monitoring installations.
The 330101-00-16-10-11-00 Bently Nevada 3300 XL 8 mm Proximity Probe may still be available for purchase and support from Apter Power beyond End-Of-Life (EOL) by the manufacturer (OEM).
Bently Nevada 330101-00-16-10-11-00 3300 XL 8 mm Proximity Probe Manuals,Datasheets,Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
Bently Nevada 330101-00-16-10-11-00 3300 XL 8 mm Proximity Probe Specs
General
- Manufacturer Bently Nevada
- Model 330101-00-16-10-11-00
- Condition New Original ready stock
- Product Family 330101-00-16-10-11-05,330101-00-16-10-01-00,330101-00-16-10-02-00
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
- Mechanical Alignment: Align the probe vertically with the bearing surface being measured using the precision adjustment bracket.
- Gap Adjustment: Use a multimeter to monitor the output voltage and set the initial static gap voltage to approximately -10 VDC.
- Cable Routing: Extension cables must be run through metal protective flexible conduits to shield against electromagnetic interference.
- Armor Fixing: Ensure the stainless steel armor layer has sufficient bending radius at wall penetrations or bends.
- Connector Sealing: After calibration, the connectors must be sealed with heat shrink tubing to prevent oil ingress.
- Steam Turbine Monitoring: Used for measuring radial vibration and axial displacement of the main shaft of steam turbines in large thermal power plants.
- Compressor Protection: Online monitoring of bearing wear and imbalance in high-speed centrifugal compressors.
- Hydropower Turbine Eccentricity: Triggering key phase pulse signals for the runout of the main shaft and the large gear of hydropower generator sets.
- Industrial Pump Protection: Early warning of mechanical failures in critical axial flow pumps and gearboxes in the petrochemical industry.
- System Power Supply: The preamplifier typically requires a stable -24 VDC standard power supply.
- Signal Monitoring: Real-time acquisition of bearing vibration peak-to-peak value by collecting dynamic voltage signals from the preamplifier.
- Linearity Verification: Maintaining a sensitivity of 7.87 V/mm within a linear range of 0.25 mm to 2.25 mm.
- Temperature Monitoring: Ensuring the operating environment temperature does not exceed the probe's designed rated tolerance limit.