Features:
- Serves as the Critical Interface Between the Machinery Surface and 3500 Monitoring System
- Integrates Patented TipLoc and CableLoc Technologies with Armored Cable Protection
- Functions Seamlessly with 3500/40M, 3500/42M, and Standard 3500 Proximitor Monitors
The Bently Nevada 330102-00-30-10-02-05 continuously converts physical gap distance between the probe tip and conductive target surface into a proportional electrical signal and transmits this signal through the armored standard cable to support steady state operation of all proximitor monitors and modules. Seamless signal integrity is standard with the 330102-00-30-10-02-05, however using an optional FluidLoc cable option will prevent oil and other liquids from leaking out of the machine through the cable's interior in fluid-contaminated environments.
The 330102-00-30-10-02-05 provides essential sensing functions common to the entire monitoring path, and is a critical component of the vibration measurement chain, directly affecting the proper, normal operation of the overall machinery protection system. One 330102-00-30-10-02-05 probe is required per measurement point depending on the desired monitoring configuration.
For critical machinery protection applications, the 3300 XL system requires the 330102-00-30-10-02-05 probe installed with proper thread engagement and perpendicular alignment to the target surface. In addition to standard single probe operation, the 330102-00-30-10-02-05 configuration also supports redundant measurement setups. The 3300 XL monitoring system executes measurement validation using the internal circuitry specified in the proximitor options.
The 330102-00-30-10-02-05 Bently Nevada 3300 XL 8 mm Proximity Probe may still be available for purchase and support from Apter Power beyond End-Of-Life (EOL) by the manufacturer (OEM).
Bently Nevada 330102-00-30-10-02-05 3300 XL 8 mm Proximity Probe Manuals,Datasheets,Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
Bently Nevada 330102-00-30-10-02-05 3300 XL 8 mm Proximity Probe Specs
General
- Manufacturer Bently Nevada
- Model 330102-00-30-10-02-05
- Condition New Original ready stock
- Product Family 330102-00-30-10-02-00,330102-00-30-10-12-05
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
- Radial Vibration: Measures dynamic shaft movement within fluid-film bearings to detect misalignment or unbalance.
- Axial Thrust Position: Monitors longitudinal shaft shifting to prevent internal rotor-to-stator contact.
- Keyphasor / Speed: Detects shaft notches to calculate exact RPM and provide phase angles for diagnostics.
- Eccentricity: Evaluates physical shaft bow or thermal warping during low-speed startup and coast-down phases.
- Loop Configuration: Requires matching 3300 XL Extension Cables and Proximitor Sensors for 5-meter or 9-meter loops.
- Backward Compatibility: Fully interchangeable with legacy, non-XL Bently Nevada 3300 series 5 mm and 8 mm systems.
- Target Material: Factory-calibrated for AISI 4140 steel. Other conductive metals require specific system recalibration.
- System Integration: Connects directly to processing modules like the Bently Nevada 3500 Machinery Protection System.
- Linear Range: Operates over an 80 mil (2.0 mm) span, typically gapped at a nominal -10 VDC mid-point.
- Side Clearance: Requires a minimum clear area of one probe tip diameter (8 mm) to avoid housing interference.
- Connector Connection: ClickLoc connectors lock with finger-tight force. Do not use tools, to prevent plating damage.
- Environmental Seal: Features a Viton O-ring tip seal and stainless steel armor to withstand high casing pressures.