Features:
- Onboard 16-bit 80196 microprocessor, watchdog timer, and 8 KB ROM provide independent and synchronized analog signal processing.
- Removable PROM firmware supports configuration retention when replacing the board during control-system maintenance.
- JCC and JDD 50-pin locking connectors, 1500 V AC isolation, and an edge-mounted diagnostic LED support secure integration and convenient inspection.
Accurate analog information is essential for turbine control, process regulation, and equipment protection. General Electric DS200TCCBG3BDC supports control cabinets by converting sensor information into data that the main control hardware can use. Pressure, liquid level, flow, and servo feedback signals can be handled within the same board-level processing environment. Independent processing reduces the workload placed on the central controller. Such capability supports stable monitoring across demanding industrial applications.
Maintenance requirements also influence the practical value of General Electric DS200TCCBG3BDC. The removable PROM arrangement allows established firmware and configuration information to remain available when hardware replacement becomes necessary. Technicians can transfer the original chip instead of rebuilding every stored instruction from the beginning. Locking ribbon-cable connectors help maintain secure internal communication during continuous machine operation. Visible LED status indication further supports rapid cabinet-level troubleshooting.
Environmental and electrical characteristics allow General Electric DS200TCCBG3BDC to function inside industrial control enclosures. The wide storage range supports transportation and inventory under varied temperature conditions. Non-condensing humidity tolerance helps accommodate typical plant environments. Galvanic isolation improves separation between sensitive analog circuits and other control sections. Combined processing, communication, and diagnostic functions make the board suitable for long-term turbine and process control service.
The DS200TCCBG3BDC General Electric Analog I/O Board may still be available for purchase and support from Apter Power beyond End-Of-Life (EOL) by the manufacturer (OEM).
General Electric DS200TCCBG3BDC Analog I/O Board Manuals,Datasheets,Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
General Electric DS200TCCBG3BDC Analog I/O Board Specs
General
- Manufacturer General Electric
- Model DS200TCCBG3BDC
- Condition New Original ready stock
- Product Family DS200TCCBG3B,DS200TCCBG3A,DS200TCCBG1BED
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
- Watchdog Timeout: Built-in 80196 chip independent hardware watchdog circuit to prevent processor crashes.
- Misinsertion Protection: 50-pin JCC/JDD interface with physical foolproof locking to prevent damage from hot-plugging cables.
- Over-Temperature Self-Conditioning: Analog amplifier circuit has hardware compensation for high-temperature drift and overheat protection mechanisms.
- Surge Noise Suppression: Input terminals integrate differential filtering and electrostatic discharge protection layers to resist high-frequency common-mode interference.
- Speed Control Architecture: Strictly follows the GE Speedtronic Mark V gas turbine control platform design standards.
- Bus Communication Specification: Compatible with the TC2000 proprietary backplane analog high-speed parallel bus transmission protocol.
- Physical Environment Resistance: Meets ANSI/ISA industrial field standards for high-frequency mechanical vibration and shock resistance.
- Firmware Migration Compliance: Employs standardized pluggable PROM firmware slots to comply with factory configuration certifications.
- Gas Turbine Fuel Blending: Used for acquiring analog signals from gas flow meters and servo valves in heavy-duty gas turbines.
- Power Plant Turbine Monitoring: Suitable for high-precision monitoring of RTD (Resistor Temperature Detector) temperatures in power plant turbine bearings.
- High-Frequency Hydraulic Feedback: Applied for data synchronization of displacement sensors in heavy-duty hydraulic cylinders of turbine control systems.
- Power Grid Bus Interlocking: Suitable for the isolation, conversion, and access of signals from PT/CT (Power Grid Transmitter) instruments in generator sets.