Features:
- Provides the Universal Safety Interface function within supported Honeywell Safety Manager controller configurations.
- Supports redundant Safety Manager controller configurations containing paired compatible USI modules.
- Provides pin-to-pin and functional compatibility with FE-USI-0002, FC-USI-0002, and FC-USI-0001 on Safety Manager R140.1 or later.
Honeywell FX-USI-0002 V1.0 provides the Universal Safety Interface function within the Safety Manager controller architecture. Honeywell identifies the module as “Universal Safety Interface MMEM CC, EUCN,” distinguishing it from field-level Universal Safety I/O modules.
Honeywell FX-USI-0002 V1.0 can operate in a redundant Safety Manager controller with another compatible USI module. Honeywell states that it can function with FE-USI-0002, FC-USI-0002, or FC-USI-0001 in the redundant controller arrangement.
Honeywell FX-USI-0002 V1.0 is the designated replacement for FE-USI-0002, FC-USI-0002, and FC-USI-0001. Pin-to-pin and functional compatibility requires Safety Manager R140.1 or later and compliance with the applicable Honeywell replacement procedure.
The FX-USI-0002 V1.0 HONEYWELL Universal Safety Interface Module may still be available for purchase and support from Apter Power beyond End-Of-Life (EOL) by the manufacturer (OEM).
Honeywell FX-USI-0002 V1.0 Universal Safety Interface Module Manuals,Datasheets,Link
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
Honeywell FX-USI-0002 V1.0 Universal Safety Interface Module
General
- Manufacturer HONEYWELL
- Model FX-USI-0002 V1.0
- Condition New Original ready stock
- Product Family FE-USI-0002, FC-USI-0002, FC-USI-0001
Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment unless listed in the above stock item description. All prices are shown in USD.
- Successor Role: FX-USI-0002 V1.0 is Honeywell's designated successor to the withdrawn FE-USI-0002 module.
- Pin Compatibility: FX-USI-0002 V1.0 is pin-to-pin compatible with FE-USI-0002, FC-USI-0002, and FC-USI-0001.
- Functional Compatibility: FX-USI-0002 V1.0 can perform the predecessor module function when installed under supported software conditions.
- Redundant Operation: FX-USI-0002 V1.0 can operate with a compatible predecessor USI module in a redundant Safety Manager controller.
- EUCN Functionality: Honeywell identifies FX-USI-0002 V1.0 as a Universal Safety Interface MMEM CC module with EUCN functionality.
- Protocol Scope: Honeywell's published FX-USI-0002 information does not identify HART, Modbus TCP, Modbus RTU, or EtherNet/IP as direct module interfaces.
- External Interfaces: Engineers should verify field and supervisory protocol requirements against the applicable Safety Manager I/O and communication hardware.
- Controller Role: FX-USI-0002 V1.0 operates within the Safety Manager controller architecture rather than as a general-purpose field protocol gateway.
- Minimum Release: Configure FX-USI-0002 V1.0 only in Safety Manager R140.1 or later.
- Enhanced Functions: Use Safety Manager R151.1 or later to access the enhanced FX-USI-0002 functions.
- Module Update: When replacing FC-USI-0001, update the configured controller module type to USI-0002.
- Application Load: Compile and load the modified application through the standard Honeywell Online Modification procedure.